Motorcycle Shuts Off When Put In Gear

I kicked it into first gear and the bike instantly shut off. I do seem to have a crack in the housing of my kickstand.

Motorcycle Shuts Off When Put In Gear - If you're looking for video and picture information related to the key word you've come to visit the ideal site. Our site gives you hints for viewing the maximum quality video and image content, hunt and locate more enlightening video articles and images that match your interests. comprises one of tens of thousands of video collections from various sources, especially Youtube, so we recommend this video for you to see. It is also possible to bring about supporting this website by sharing videos and images that you like on this site on your social media accounts such as Facebook and Instagram or tell your closest friends share your experiences concerning the ease of access to downloads and the information that you get on this site. This site is for them to stop by this website.

What S With False Neutrals Mc Garage Youtube

I had kinds of codes showing on the bike and Ive also replaced the cpks tip over sensor gear position sensor throttle position sensor and replaced the chain and sprocket because it had so much rust on it he kept motorcycle in carport in Seattle weather.

Motorcycle shuts off when put in gear. Just like you turned the ignition off which is what it does. Got the bike typ start up but when I kicked it into gear itd cut right back off. OP push your bike 3 ft with the engine off in gear clutch in and report back.

I have had to push the bike home a couple times due to the bike kept cutting out when put into first gear. Our man Redpath at MotoGP Werks says a really big clunk when shifting into first often means a warped steel plate especially if the bike creeps when you rev it with the clutch in and in gear. Yahama vstar 1100 dies when put into gear Could be a couple things first make sure your kick stand is all the way up if so you probably have either a bad kickstand or clutch switch.

They can be checked with a meter set on ohms if you get the same reading in both in and out the switch is bad Frank. I know what you might be thinking but I have now checked out the side stand switch and clutch lever switch and every thing seems fine and it has just done it again to me. You can save a bunch of time and just remove the switch from the frame without un-plugging it.

I did mine years ago just for preventive maintainance after reading of the issue. It will usually break loose and not be a problem after that. That solved the cutting out when letting out the clutch issue but not the putting the bike in gear issue.

After giving up I got off the bike and let it sit for about 5 minutes. The bike will shut off if you put it in gear while the kickstand is down. If the kickstand switch staysfails open with the bike in gear it will die just shut off as you let the cluch out.

To troubleshoot I took off the switch on the clutch lever and let it dangle. At 18000 miles if moneys not super-tight you may as well replace the steels too. Bike fires up and runs perfect as soon as you put it in gear she shuts off as if you hit the kill switch.

My 99 Roadstar has the habit of always shutting off when I knock it into first. Saves lifting the tank finding the connector end etc. The oil drys up on the plates and they stick together.

Pull in the clutch and put it in first gear the bike lunges forward and shuts off. Let it warm up a bit. As soon as you put it in gear cuts off like you flipped the main switch.

Troubleshooting done so far. Hello had this problem with atv the shifter fork sometimes will rust inside the motor especially if it has been setting or the gear may be stuck on shifter fork you may have to split motor and fix the problem very hard job to do you might try some lucas in your oil or other oil additives try and tap gear shifter with motorcycle rear tire off ground while running it might break loose if not probably. - unplugged clutch sensor issue continues.

Always had to warm the bike up thoroughly to be able to push it when shut off. Its a wet clutch system. If its hard initially and then fine its as Ariel says.

Shouldnt take 15 minutes to go thru the switch. Note to self. What I do on cold starts is to select first gear with the motor off pull the clutch in and.

Revs idles and turns off and then restarts just as it should. I put it back into neutral and started it up. - found out that the kickstand sensor needs to be jumped touched the 2 prongs together issue continues.

I tried to put it into first gear another 5 or 6 times and every time it would shut the bike off. GSF600 FZR600 x2 ZXR750 XT600 Tenere CB125 CZ125 ETZ 250 ER5 CCM R30 DRZ400 RF600x4 RF900x2 GS500 VTR1000F 640 SMC CB250 NIGHTHAWK GT550x3 GPX750 TE610 CB500 X11x2 SV650 ZING 125 TL1000RCB250. Cant roll it in gear with the engine off.

Be prepared because it will lurch forward. 02 1500 Mean Streak. Hold thefront brake ALWAYS when shifting a cold bike into first.

Backed out of the parking spot. One is a clutch switch to stop you trying to start the bike in gear without pulling the clutch in - you can hear this click on most bikes if you pull the lever in with the engine off. Put on the brakes raise the idle and put the bike in gear.

Put a short stool next to the bike put the switch atop it. That starter cutoff relay does seem to be working because the bike starts and runs very well. My bike shuts off after I put it into gear any gear.

Well first the bike would shut off if I had it in neutral stand down and let the clutch out. My model year 2003 can be left idling while the kickstand is down so that isnt an issue. The second problem could be that the clutch plates are stuck.

3 Nov 20 2005. Discussion Starter 1 Jan 31 2010. This is very common if the bike has not been used for a long time.

Modern-ish motorcycles have two simple switches to prevent you doing stupid things that might make you fall off. - unplugged kickstand sensor issue continues. And tried to take off.